With the assistance of our technical team of experts, we are engaged in offering a wide range of Compression & Pipe Fittings. These fittings are widely appreciated by our clients for simple construction, efficiency, low cost and easy of assembly. Compression & Pipe Fittings are widely used with copper, brass and aluminum for connecting gasoline, grease, oil, water, vacuum and air lines.


Specifications:

Assembly Instructions	Slide nut, Sleeve onto tubing. The thread end of the nut must face out. Insert the tube into the fitting. Be sure the tube is bottomed on the fitting shoulder. Assemble nut to body, and tighten the nut.
Materials-Elbow and Tees	Brass forgings-Pioneer compression fittings are made from BS-218 material. The exceptional strength of forge fittings (Over 80% stronger than castings) provides an extra safety factor.
Connectors, Unions and Nuts	Stress relieved brass bar stock-BS-249
Temperature Ranges	From - 650 F - 2500 F
Vibration	Fair resistance to vibration or tube movement, depending on applications involved. Long nut for additional resistance to vibration.

We offer Different types of Compression and pipe fittings Such as:


Brass Compression Tube Fittings :

MALE STUD, STUD ELBOW, RUN TEE, BRANCH TEE, FEMALE RUN TEE, FEMALE BRANCH TEE, FEMALE BRANCH TEE, FEMALE ELBOW, FEMALE STUD,

TUBE TO TUBE FITTINGS-  ELBOW, TEE, BULKHEAD,

FERRUL AND NUT-  FERRUL10, NUT


PIPE FITTINGS:

MALE FEMALE ELBOW , UNION ELBOW, STREET ELBOW, REDUCING STREET ELBOW, 45° STREET ELBOW, UNION TEE , MALE RUN TEE, UNION CROSS, UNION COUPLING
BUSHING, REDUCING BUSHING, CLOSE NIPPLE, LONG NIPPLE, HEX NIPPLE, REDUCING NIPPLE, PLUG, SLOTTED HEAD PLUG, ADAPTER, LOCK NUT, CAP.

These brass compression fittings and pipe fittings are available in different dimensions:

Sizes-  2 - 25 Tube O.D. T mm
Thread -  1/8 to 1 NPT


Working Pressure Ranges:

Temperature and type of tubings used are important factors. However, the following table is good guide for proper selection at temperature 60 F.

Applications:

Use with copper, brass and aluminium. Not recommended for steel tubing manufactured for low & medium pressure tubing connection work where excessive vibrations or tube movement is not involved. This fittings is widely used for connecting gasoline, grease, oil, water, vacuum and air lines    

For more details refer PDF attached under the photograph.

Quickest and Easiest to assemble tubing into the PUSH-TO-LOCK Fittings, just push the tubing into fitting upto the bottom and leakproof connection is made.

Quickest and Easiest to Dis assembly is achieved by pushing release collar. This disengages the gripper collet and allows the tubing to be pulled out. It's that simple.

Push it's connected; push/pull it's disconnected.

No Tubing Twist

The gripper collet and tubing are free to rotate within the fitting body. If the tube is rotated, it will not twist or weaken.

Swing Clearance Problems Eliminated

Elbows and tees are available with an integral swivel at the male pipe end. This allows the pipe thread to be tightened without rotating the elbow or tee. It also permits the pipe thread to be tightened without worry about where the other end of the fitting will point, as it can be rotated into position after the pipe thread is tight.

Material of Construction

• Body : Brass
• Collet : Spring Steel [S.S.]
• Seal : Nitrile Rubber / Viton for higher temperature.
• Teflon pre-coated male taper threads

Working Pressure and Temperature Ranges

Zero to 60oC at up to 10 Bar. Vacuum applications are dependent upon temperature and type of tubing being used.

Application

• Compressed air lines on pneumatic circuits in any industry.
• Fuel lines in Automobile industry.
• Centralised lubrication systems.
• For conveying any gas or liquid.

Recommended Tubing

• Suitable tubing material : Nylon 6, Nylon 11, Polyethylene, Polyurethane.
• Recommended Tolerance on O.D. of tube. ± 0.1 mm.

Assembly Instructions

Cut Nylon, Polyurethane and Polyethylene tubing squarely using Pioneer SQUARE CUT  tube cutter. Metal tubing should be cut squarely and be free of burrs. Insert end of tubing until it bottoms in fitting. Depressing the release button allows the tubing to be removed.

Ordering Information

To Order, simply specify catalogue number for configuration and size desired.

Sizes & Pipe Threads

• Tube Sized  : 4MM to 12MM
• Thread Type : 1/8" to 1/2" B.S.P.
• Metric fittings are also available.

Marketing and Technical Services

Wide Dealer network will assist you in selecting the most appropriate fittings and tubing for your application, and also make them available to you whenever your need arises. Ongoing Research and Development constantly striving to improve the product to meet more stringent conditions. (Hence product compositions and specifications may change periodically).